[Jun-2025] EMC D-PVM-OE-01 Exam Practice Test Questions - RealVCE
Updated Certification Exam D-PVM-OE-01 Dumps - Practice Test Questions
NEW QUESTION # 22
What is the status of the Host I/O paths to the target array after a Non-Disruptive Migration Cutover?
- A. Dead
- B. Inactive
- C. Write Disabled
- D. Read/Write Enabled
Answer: D
NEW QUESTION # 23
How does Unisphere 360 differ from Unisphere for PowerMax?
- A. Unisphere for PowerMax provides both GUI and SYMCLI access to PowerMax and VMAX arrays.
Unisphere 360 provides only GUI access to PowerMax and VMAX arrays. - B. Unisphere for PowerMax provides only GUI access to PowerMax and VMAX arrays. Unisphere 360 provides both GUI and SYMCLI access to PowerMax and VMAX arrays.
- C. Unisphere for PowerMax is the management console for PowerMax and VMAX Family arrays.Unisphere 360 provides centralized monitoring for DMX, VMAX Family, and PowerMax arrays.
- D. Unisphere for PowerMax provides centralized monitoring for DMX, VMAX Family, and PowerMax arrays. Unisphere 360 is the management console for PowerMax and VMAX Family arrays.
Answer: A
NEW QUESTION # 24
An array has reached its capacity m the Storage Resource Pool (SRP). What is the function of the SRP Reserved Capacity?
- A. Accommodate SRDF/A delta sets
- B. Provide space for snapshot copies
- C. Accommodate new host writes
- D. Provide space for snapshot deltas
Answer: C
NEW QUESTION # 25
What is a feature unique to the PowerMax 8500 compared to the PowerMax 2500?
- A. Persistent Memory
- B. Mainframe Connectivity
- C. InfiniBand Switches
- D. Storage Class Memory
Answer: C
Explanation:
Step by Step Comprehensive Detailed Explanation:
Both the PowerMax 2500 and 8500 utilize NVMe over Fabrics (NVMe-oF) for high-speed data transfer.
However, they differ in their internal fabric architecture:
* PowerMax 2500:Uses a direct NVMe/PCIe connection between the compute nodes and the Dynamic Media Enclosures (DMEs).
* PowerMax 8500:Employs a fully switched InfiniBand (IB) fabric for all NVMe-oF traffic. This means that the compute nodes and DMEs are interconnected through InfiniBand switches, providing a high- performance, low-latency, and scalable fabric for data transfer.
Therefore, the use of InfiniBand switches is a feature unique to the PowerMax 8500 compared to the PowerMax 2500.
Why other options are incorrect:
* A. Persistent Memory:Both PowerMax 2500 and 8500 utilize Storage Class Memory (SCM), which is a type of persistent memory.
* B. Mainframe Connectivity:Both models support mainframe connectivity.
* C. Storage Class Memory:As mentioned above, both models use SCM.
References and documents of Dell's public documentation for PowerMax Operate v.2:
* PowerMax 2500 and 8500 Dynamic Fabric-A High-Performance Clustered Architecture for Enterprise Storage:This white paper provides a detailed comparison of the Dynamic Fabric architecture in both models, highlighting the use of InfiniBand switches in the PowerMax 8500. You can find this document on the Dell Technologies Info Hub.
* Dell PowerMax Family: Essentials and Best Practices Guide:This guide offers a general overview of the PowerMax family, including the 2500 and 8500 models. It may provide context for understanding the differences in their architecture and features.
NEW QUESTION # 26
Which product(s) support(s) only 7+1 in RAID 5 configurations?
- A. VMAX All Flash
- B. VMAX All Flash and PowerMax 2000
- C. VMAX3
- D. VMAX All Flash and PowerMax 8000
Answer: D
NEW QUESTION # 27
What function can a storage administrator enable on the Port Attributes page?
- A. Select Mgt Option
- B. ORS Ceiling
- C. Manage Protocol
- D. Volume Set Addressing
Answer: A
NEW QUESTION # 28
Place the steps in the correct order to create clone copy sessions of device groups.
Answer:
Explanation:
Explanation:
Here's the correct sequence of steps along with explanations:
Correct Order:
* Select Data Protection > Device Groups from the navigation pane.
* Why:This is the starting point within Unisphere for PowerMax. You need to navigate to the section where device groups are managed and where TimeFinder operations are initiated.
* Select a PowerMax array.
* Why:In an environment with multiple PowerMax arrays, you must specify the array on which you want to create the clone copy sessions.
* Select a group and click Create Pairs.
* Why:You are selecting the specific device group that will be the source for the clone operation and choosing the "Create Pairs" action to initiate the clone session creation process. This implies you are creating a clone from an existing group of devices.
* Select a source type and a target type.
* Why:This step defines the characteristics of the source and target devices for the clone session.
This could involve selecting from different storage groups, specifying thin or thick provisioning, or other relevant settings. Note that in a clone context, the "target type" often refers to how the clone will be linked to the source (e.g., a full copy or a linked target).
* Click Run Now to run the operation.
* Why:After configuring all the settings for the clone session, this action triggers the actual creation of the clone pairs based on the selected source and target types and other parameters.
* Click the TimeFinder Clone tab to view the list of clones.
* Why:Once the operation has been initiated, this is how you would verify that the clone sessions were created successfully and monitor their status.
* Select Data Protection > Device Groups from the navigation pane.
* Select a PowerMax array.
* Select a group and click Create Pairs.
* Select a source type and a target type.
* Click Run Now to run the operation.
* Click the TimeFinder Clone tab to view the list of clones.
NEW QUESTION # 29
A host is connected to two PowerMax arrays with SRDF/Metro Host l/Os cannot be delivered across the SRDF link. The devices in the SRDF group have been forced into a Not Ready state to the host Which attribute is set on the SRDF group to cause this behavior?
- A. Limbo Period
- B. Local Link Domino
- C. Local Auto Link Recovery
- D. Update After Resume Link
Answer: C
NEW QUESTION # 30
From an application perspective what should be done prior to performing an SRDF Fallback operation?
- A. Stop accessing the R2 devices
Run the command and then start accessing the R1 devices - B. Stop accessing the R2 devices
Start accessing the R1 devices before running the command - C. Continue accessing the R2 devices
Run the command and then start accessing the R1 devices - D. Continue accessing the R2 devices
Start accessing the R1 devices before running the command
Answer: A
NEW QUESTION # 31
Place the steps to create a snapshot in Unisphere for PowerMax in the correct order
Answer:
Explanation:
Explanation:
Okay, I'm ready to arrange those steps for creating a snapshot in Unisphere for PowerMax in the correct order, based on the image provided.
Here is the correct sequence, along with explanations:
Correct Order:
* Select a PowerMax storage system from the navigation pane Storage > Storage Groups.
* Why:This is the starting point in Unisphere. You need to navigate to the "Storage Groups" section within the specific PowerMax array where you intend to create the snapshot.
* Select a Storage Group and click Protect.
* Why:You're choosing the storage group that contains the data you want to snapshot. Clicking
"Protect" initiates the process of creating a data protection operation (in this case, a snapshot).
* In the Protect Wizard, if not already selected, select Create a Snapshot using SnapVX from the Select Technology tab and click Next.
* Why:This specifies that you want to use the SnapVX technology to create a snapshot. SnapVX is the snapshot feature in PowerMax arrays.
* In the Configure SnapVX page, select whether to create a snapshot or reuse an existing snapshot along with the expiry type.
* Why:Here, you define the core parameters of the snapshot:
* Create a new snapshot:This is what you'd typically do for a new point-in-time copy.
* Reuse an existing snapshot:In some cases, you might want to update an existing snapshot.
* Expiry type:This determines how long the snapshot will be retained (e.g., a specific duration or until manually deleted).
* Click Advanced Options to see the advanced options and Enable Secure Snaps.
* Why:This allows you to configure more granular settings for the snapshot, including:
* Secure Snaps:Enabling this option prevents the snapshot from being deleted before its expiry time, adding an extra layer of protection.
* Verify the selections in the summary page, and click Run Now or Add to Job List.
* Why:This is the final step before creating the snapshot:
* Summary page:Review all the settings you've configured.
* Run Now:Immediately creates the snapshot.
* Add to Job List:Schedules the snapshot creation for later.
* Select a PowerMax storage system from the navigation pane Storage > Storage Groups.
* Select a Storage Group and click Protect.
* In the Protect Wizard, if not already selected, select Create a Snapshot using SnapVX from the Select Technology tab and click Next.
* In the Configure SnapVX page, select whether to create a snapshot or reuse an existing snapshot along with the expiry type.
* Click Advanced Options to see the advanced options and Enable Secure Snaps.
* Verify the selections in the summary page, and click Run Now or Add to Job List.
NEW QUESTION # 32
Four snapshots of a single source volume have been created. The snapshots were created with the same name at 8:00 AM, 10:00 AM, 12:00 PM: and 2:00 PM.
What is the generation number of the snapshot created at 2:00 PM?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
Explanation:
Step by Step Comprehensive Detailed Explanation:
In TimeFinder SnapVX, snapshots of a source volume are assigned generation numbers. These numbers indicate the order in which the snapshots were created. The first snapshot taken has a generation number of 0, the second has 1, and so on.
In this case, four snapshots were created at different times:
* 8:00 AM (Generation 0)
* 10:00 AM (Generation 1)
* 12:00 PM (Generation 2)
* 2:00 PM (Generation 3)
Therefore, the snapshot created at 2:00 PM has a generation number of3.
References and documents of Dell's public documentation for PowerMax Operate v.2:
* Dell Solutions Enabler 10.0.0 TimeFinder SnapVX CLI User Guide:This guide provides detailed information about SnapVX features and functionalities, including how generation numbers areassigned to snapshots. You can find this document on the Dell Support website by searching for "Solutions Enabler TimeFinder SnapVX CLI User Guide."
NEW QUESTION # 33
What is an update operation in SRDF on PowerMax arrays?
- A. process to retain the data on the target R2 side
- B. A process used to return to the original production site after a failover event
- C. A process that initiates an incremental copy from the target R2 to the source R1
- D. A process that allows separate hosts to access the same data independently
Answer: C
Explanation:
Step by Step Comprehensive Detailed Explanation:
In SRDF (Symmetrix Remote Data Facility), an "update" operation refers to a specific process where changes made on the target (R2) side are copied back to the source (R1) side. This is typically used in disaster recovery scenarios where:
* Failover:A failover occurs, and the target (R2) becomes the active production site.
* Data Modification:Data is modified or updated on the target (R2) while it's acting as the primary.
* Update Operation:An "update" is initiated to synchronize the changes from the target (R2) back to the source (R1), ensuring that the source has the latest data.
This process is crucial for maintaining data consistency and ensuring a smooth transition back to the original production site after a failover event.
Why other options are incorrect:
* A. process to retain the data on the target R2 side:This is not specific to an "update" operation. Data retention on the target is a general aspect of SRDF.
* B. A process used to return to the original production site after a failover event:While an "update" is part of the failback process, it's not the entire process itself. Failback involves other steps like reversing replication direction and restoring host access.
* D. A process that allows separate hosts to access the same data independently:This describes a different SRDF configuration (like Active/Active) and is not related to the "update" operation.
References and documents of Dell's public documentation for PowerMax Operate v.2:
* Dell Solutions Enabler 10.0.0 SRDF Family CLI User Guide:This guide provides detailed information about SRDF commands and operations, including the symrdf update command used to initiate an update from R2 to R1. You can find this document on the Dell Support website by searching for "Solutions Enabler SRDF Family CLI User Guide."
* Dell PowerMax Family: Essentials and Best Practices Guide:This guide offers a comprehensive overview of SRDF and its functionalities, including disaster recovery scenarios and the use of the
"update" operation.
NEW QUESTION # 34
A systems administrator wants to know how to convert SRDF ports back to FA ports on their PowerMax array What information should be provided'?
- A. Array will require an upgraded bin file to complete the change
- B. A Simplified SymmWin script must be run from the PowerMax MMCS
- C. Change can only be completed using Solutions Enabler or an upgraded bin file
- D. Make the change using Solutions Enabler or Unisphere for PowerMax
Answer: A
NEW QUESTION # 35
Which emulations can be added through the SYMCLI?
- A. EDS, FA, and SE
- B. RF, SE, and DX
- C. RE, RF, and SE
- D. IM, DX, and RF
Answer: C
NEW QUESTION # 36
Which Threshold levels must be set when creating customized threshold alerts in Unisphere for PowerMax?
- A. Warning, Marginal, and Critical
- B. Warning, Critical, and Fatal
- C. Stable, Marginal, and Critical
- D. Stable, Critical, and Fatal
Answer: B
NEW QUESTION # 37
A Storage Group is serving host read/write I/O. The Storage Administrator started an MDM migration and ran a symdm sync -stop command, putting the migration in a CutoverNoSync migration state Where does the customer data in the Storage Group reside?
- A. Only on the source array
- B. On both the source and the target array
- C. Only the target array
Answer: B
Explanation:
Step by Step Comprehensive Detailed Explanation:
In an MDM (Migration for Dell EMC) migration, data is moved from a source array to a target array. When the symdm sync -stop command is issued, it puts the migration into the CutoverNoSync state. This state signifies that:
* Synchronization Stopped:Active data synchronization between the source and target arrays has been stopped.
* Data on Both Arrays:However, the customer data still resides onboththe source and target arrays. This is because the CutoverNoSync state is a transitional state that allows for a controlled cutover to the target array.
The next step would typically involve a cutover operation, where host access is switched to the target array, and the source array is removed from the migration configuration.
Why other options are incorrect:
* A. Only the target array:While the goal is to eventually have the data only on the target, in the CutoverNoSync state, data still exists on both arrays.
* B. Only on the source array:Data has already been partially or fully copied to the target array during the migration process.
References and documents of Dell's public documentation for PowerMax Operate v.2:
* Dell Solutions Enabler 10.0.0 CLI User Guide:This guide provides detailed information about the symdm command and its various options, including the sync -stop command and the CutoverNoSync state. You can find this document on the Dell Support website by searching for "Solutions Enabler CLI User Guide."
* Dell PowerMax Family: Essentials and Best Practices Guide:This guide may offer general information about data migration and the different states involved in the process.
NEW QUESTION # 38
Where are the Host l/Os directed to when the Storage Group is in a Non-Disruptive Migration CutoverReady state?
- A. Source array only
- B. Held in host cache
- C. Target array only
- D. Source and target arrays
Answer: A
NEW QUESTION # 39
Your organization is preparing for a major software update, and it is crucial to ensure data integrity during this process. As a system administrator, create a secure snapshot named "Stor1" from the storage group
"StorGroup1." The snapshot cannot be deleted for two days to safeguard against any potential data loss during the update.
Using the simulator, complete the operation.
Answer:
Explanation:
See the explanation for step by step solution.
Explanation:
We need to create a secure snapshot named "Stor1" from the storage group "StorGroup1" in the Unisphere for PowerMax simulator, and the snapshot should be protected from deletion for two days.
Here's a step-by-step guide on how to do this, based on typical Unisphere functionality:
Steps:
1. Launch the Simulator and Navigate to the Storage Groups Section
* Open Unisphere for PowerMax in your web browser.
* Log in to the simulator (you should already be logged in with the array SID 1762 selected).
* In the left-hand navigation pane, click onStorageand then selectStorage Groups.
2. Locate and Select "StorGroup1"
* In the Storage Groups view, you'll see a list of all storage groups on the array.
* Find the storage group named "StorGroup1".
* Click on the name "StorGroup1" to open its details view.
3. Initiate the Snapshot Creation Process
* Within the "StorGroup1" details view, look for an option related to creating snapshots or protecting the storage group. This might be a button labeled:
* "Protect"
* "Create Snapshot"
* "SnapVX"
* Or an icon representing snapshot creation.
* Click the appropriate button or icon to start the snapshot creation process.
4. Configure Snapshot Settings
* A new window or panel will appear, allowing you to configure the snapshot settings.
* Snapshot Name:Enter Stor1 as the snapshot name.
* Snapshot Technology:SelectSnapVX(or a similar option) as the snapshot technology.
* Secure Snapshot:This is crucial. Look for an option labeled "Secure Snapshot," "Enable Secure Snap,"
"Secure Snap," or something similar.Check this option.
* Retention/Expiration:You need to set the retention period for the secure snapshot. This will define how long the snapshot cannot be deleted. There are usually a few ways to configure this:
* Expiration Time:Set an explicit expiration date and time that is two days from now.
* Retention Period:Specify a retention period of 2 days.
* No Expiry:This option is not what we want here. We want the snap to be secure for 2 days.
* Choose the appropriate option to make the snapshot undeletable for two days.
* Other Settings:Review any other available settings. You might be able to choose between creating a new snapshot or linking to an existing one. Select the option to create anew snapshot.
5. Create the Snapshot
* After configuring all the snapshot settings, review them carefully to ensure they are correct.
* Click the button to create the snapshot. This button might be labeled:
* "Run Now"
* "OK"
* "Create"
* "Finish"
6. Verify Snapshot Creation (Optional)
* After the snapshot creation operation completes, you can verify that the snapshot was created successfully:
* Go back to the "StorGroup1" details view.
* Look for a tab or section related to snapshots (e.g., "Snapshots," "TimeFinder," "Local Replication").
* You should see the "Stor1" snapshot listed there, and its status should indicate that it's a secure snapshot with the correct retention period (2 days).
NEW QUESTION # 40
What are the two configuration rules that apply to SRDF groups and connections during Non-Disruptive Migrations'?
- A. Two DM RDF groups are created per SG migration session
- B. A single array cannot have multiple DM RDF groups
- C. DM RDF groups are configured with a minimum of one path
- D. The source and target arrays are at most one hop away from the control host
- E. RF and RE ports are supported, with RF ports being selected if both types are available
Answer: C,D
Explanation:
Step by Step Comprehensive Detailed Explanation:
Non-Disruptive Migration (NDM) is a feature in PowerMax that allows you to migrate data between storage arrays without any downtime or disruption to host applications. During NDM, SRDF (Symmetrix Remote Data Facility) is used to replicate data between the source and target arrays. Here are the configuration rules that apply to SRDF groups and connections during NDM:
* A. The source and target arrays are at most one hop away from the control host:The control host, which manages the NDM process, must have direct connectivity to both the source and target arrays.
This ensures efficient communication and control during the migration.
* E. DM RDF groups are configured with a minimum of one path:SRDF groups used for NDM (DM RDF groups) must have at least one active path between the source and target arrays. This ensures that data can be replicated continuously during the migration.
Why other options are incorrect:
* B. Two DM RDF groups are created per SG migration session:This is not a strict requirement. The number of DM RDF groups may vary depending on the configuration and the specific NDM operation.
* C. RF and RE ports are supported, with RF ports being selected if both types are available:While RF and RE ports are supported for SRDF, there's no specific preference for RF ports during NDM. The choice of ports depends on the overall network configuration and availability.
* D. A single array cannot have multiple DM RDF groups:An array can have multiple DM RDF groups if needed for different NDM operations or configurations.
References and documents of Dell's public documentation for PowerMax Operate v.2:
* Dell PowerMax Family: Essentials and Best Practices Guide:This guide provides an overview of NDM and its requirements, including information about SRDF configuration.
* Dell Solutions Enabler 10.0.0 CLI User Guide:This guide provides detailed information about SRDF commands and configuration options, which are relevant for NDM operations.
NEW QUESTION # 41
Place the steps in the correct order for performing a Non-Disruptive Migration
Answer:
Explanation:
Explanation:
* Set up the migration environment to migrate applications from the source array to the target array.
* Examine the specific storage for the applications on the source array and automatically provision equivalent storage on the target array.
* Initiate data synchronization from the source to the target and cutover to make source array paths inactive so target array services all host I/O.
* Commit the necessary changes after the source to target data synchronization is complete and all application data has been migrated to the target.
* Remove the configured array-to-array connectivity for the data migration pathway on both storage arrays.
Correct Order:
* Set up the migration environment to migrate applications from the source array to the target array.
* Why:This is the initial setup phase, where you configure the necessary settings on both the source and target arrays to enable the migration. This involves actions like:
* Verifying compatibility between the source and target arrays.
* Ensuring that the required licenses are in place (e.g., NDM license).
* Configuring network connectivity (FC or iSCSI) for data transfer between the arrays.
* Examine the specific storage for the applications on the source array and automatically provision equivalent storage on the target array.
* Why:Before migrating data, you need to ensure that the target array has the appropriate storage capacity and configuration to host the applications.
* How:NDM can often automatically provision equivalent storage on the target based on the source configuration. This includes creating storage groups, volumes, and masking views that mirror the source.
* Initiate data synchronization from the source to the target and cutover to make source array paths inactive so target array services all host I/O.
* Why:This is the core of the migration process. Data is copied from the source to the target while the application continues to run. Cutover is the final step where I/O is redirected to the target array.
* How:
* Synchronization:Data is copied in the background.
* Cutover:Once synchronization is complete, a brief cutover is performed. In a well-planned NDM, this cutover is designed to be within the I/O timeout limits of most applications.
* Commit the necessary changes after the source to target data synchronization is complete and all application data has been migrated to the target.
* Why:This step finalizes the migration and makes it permanent.
* What it involves:The migration session is acknowledged and the configuration is finalized on the target array.
* Remove the configured array-to-array connectivity for the data migration pathway on both storage arrays.
* Why:After the migration is complete, the temporary connections used for data transfer between the arrays should be removed to free up resources and maintain a clean configuration.
* What it involves:This typically means removing the FC zones or iSCSI settings that were configured specifically for the NDM process.
NEW QUESTION # 42
Your organization is planning to expand its data center capacity and must configure a new PowerMax 2500 system. The goal is to ensure high performance and sea abi ity Whi e maintaining redundancy Which configuration option is specific to the PowerMax 2500 system?
- A. Scales from one to a maximum of two node pairs
- B. Supports up to 1 5 PB of effective capacity
- C. Supports up to 16 nodes
- D. Uses Storage Class Memory
Answer: A
Explanation:
Step by Step Comprehensive Detailed Explanation:
The Dell PowerMax 2500 is a mid-range storage array designed for enterprise environments. It offers a balance of performance, capacity, and scalability.
* Scalability:The PowerMax 2500 scales from a single node pair to a maximum of two node pairs. This allows for increased performance and capacity as needed. Each node pair provides processing power, cache memory, and connectivity.
Why other options are incorrect:
* A. Supports up to 16 nodes:This is incorrect. The PowerMax 8500, the higher-end model, supports up to 16 nodes.
* B. Supports up to 15 PB of effective capacity:While the PowerMax 2500 offers significant capacity, its maximum effective capacity is lower than 15 PB.
* D. Uses Storage Class Memory:Both the PowerMax 2500 and 8500 utilize Storage Class Memory (SCM) for enhanced performance.
References and documents of Dell's public documentation for PowerMax Operate v.2:
* Dell PowerMax 2500 Hardware Information Guide:This guide provides detailed technical specifications for the PowerMax 2500, including its scalability options, node configurations, and capacity limits. You can find this document on the Dell Support website by searching for "PowerMax
2500 Hardware Information Guide."
* Dell PowerMax Family: Essentials and Best Practices Guide:This guide offers a general overview of the PowerMax family, including the 2500 and 8500 models. It highlights the key differences in scalability and performance between the two models.
NEW QUESTION # 43
When listing the details of a snapshot, what does "Total Deltas" reference?
- A. Difference between the snapshot and a newer snapshot
- B. Difference between the source and target
- C. Difference between the snapshot and the source
- D. Difference between the snapshot and the target
Answer: A
NEW QUESTION # 44
Which tasks can a storage administrator manage from the Data Protection menu in the Unisphere for PowerMax?
- A. Configure Data Protection for z systems
- B. Review the audit log for unwanted logins
- C. Convert front-end ports to SRDF ports
- D. Configure and manage SRDF groups
Answer: D
Explanation:
Step by Step Comprehensive Detailed Explanation:
The "Data Protection" menu in Unisphere for PowerMax provides a centralized location for managing various data protection features and functionalities. Specifically, it allows storage administrators to:
* Configure and manage SRDF groups:SRDF (Symmetrix Remote Data Facility) is a key technology for disaster recovery and data replication in PowerMax. The Data Protection menu enables administrators to create, modify, and monitor SRDF groups, establish replication relationships between devices, and control replication settings.
Why other options are incorrect:
* A. Convert front-end ports to SRDF ports:This is typically done through the "System > Hardware" or "Connectivity" sections of Unisphere, where port configurations are managed.
* C. Configure Data Protection for z Systems:While PowerMax supports mainframe environments, the specific configuration for z Systems might involve specialized tools or interfaces.
* D. Review the audit log for unwanted logins:Audit logs and security-related events are usually found in the "Monitoring" or "Security" sections of Unisphere.
References and documents of Dell's public documentation for PowerMax Operate v.2:
* Dell Unisphere for PowerMax 10.0.0 Online Help:The online help for Unisphere provides a detailed explanation of the functionalities available in each menu, including the Data Protection menu. You can access this help within Unisphere itself or on the Dell Support website.
* Dell PowerMax Family: Essentials and Best Practices Guide:This guide offers a general overview of data protection features in PowerMax and how they are managed through Unisphere.
NEW QUESTION # 45
A non-production environment has been created with a VMFS Datastore named TestDS and a virtual machine named TestVM. SRDF/S has been configured between two PowerMax arrays One ESXi server is connected to the R1 device and another is connected to the R2 device. The VMFS Datastore resides on the R1 device.
The systems administrator wants to test the environment for disaster recovery readiness To simulate a disaster on the R1 side a graceful failover will be done. What is the correct sequence of steps on the R1 side of the test environment to perform a graceful failover?
Answer:
Explanation:
Explanation:
1.Shunt down testvm on the primary esxi server
2. unregister testvm.
3.Unamount testds .
4.perform a failover operation.
NEW QUESTION # 46
......
Updated Verified D-PVM-OE-01 dumps Q&As - Pass Guarantee or Full Refund: https://www.realvce.com/D-PVM-OE-01_free-dumps.html
D-PVM-OE-01 PDF Questions and Testing Engine With 156 Questions: https://drive.google.com/open?id=1XbPQV7lqNglTvKTGBjuw3p-y02Rj2_vw