Guide (New 2024) Actual Fortinet NSE7_SDW-7.0 Exam Questions
NSE7_SDW-7.0 Exam Dumps Pass with Updated 2024 Certified Exam Questions
Fortinet NSE7_SDW-7.0 exam is a rigorous test that requires candidates to have a deep understanding of SD-WAN technologies and concepts. NSE7_SDW-7.0 exam consists of 60 multiple-choice questions that need to be completed in 120 minutes. Candidates are required to score a minimum of 50% to pass the exam. NSE7_SDW-7.0 exam is available in multiple languages, including English, Japanese, and Chinese.
Fortinet NSE7_SDW-7.0 exam is suitable for IT professionals with experience in networking, security, and cloud computing. Candidates must have a deep understanding of networking technologies, such as TCP/IP, LAN, and WAN, and be familiar with network security concepts, such as firewalls, VPNs, and intrusion prevention systems. They must also have experience with cloud computing technologies, such as virtualization, containers, and cloud-based services.
NEW QUESTION # 16
Refer to the exhibits.
Exhibit B -
Exhibit A shows the system interface with the static routes and exhibit B shows the firewall policies on the managed FortiGate.
Based on the FortiGate configuration shown in the exhibits, what issue might you encounter when creating an SD-WAN zone for port1 and port2?
- A. port1 is referenced in a firewall policy.
- B. port1 is assigned a manual IP address.
- C. port1 and port2 are not administratively down.
- D. port2 is referenced in a static route.
Answer: A
NEW QUESTION # 17
Refer to the exhibit.
Based on the exhibit, which two actions does FortiGate perform on sessions after a firewall policy change? (Choose two.)
- A. FortiGate evaluates new sessions.
- B. FortiGate does not change existing sessions.
- C. FortiGate flushes all sessions.
- D. FortiGate terminates the old sessions.
Answer: A,B
Explanation:
FortiGate not to flag existing impacted session as dirty by setting firewall-session-dirty to check new. The results is that FortiGate evaluates only new session against the new firewall policy.
NEW QUESTION # 18
Which two statements about the SD-WAN zone configuration are true? (Choose two.)
- A. The default zones are virtual-wan-link and SASE.
- B. You can delete the default zones.
- C. An SD-WAN member can belong to two or more zones.
- D. The service-sla-tie-break setting enables you to configure preferred member selection based on the best route to the destination.
Answer: A,D
NEW QUESTION # 19
Refer to the exhibit.
Based on the exhibit, which statement about FortiGate re-evaluating traffic is true?
- A. Firewall policy ID 1 has source NAT disabled.
- B. FortiGate has terminated the session after a change on policy ID 1.
- C. Changes have been made on firewall policy ID 1 on FortiGate.
- D. The type of traffic defined and allowed on firewall policy ID 1 is UDP.
Answer: C
NEW QUESTION # 20
Refer to the exhibits.
Exhibit A -
Exhibit B -
Exhibit A shows a site-to-site topology between two FortiGate devices: branch1_fgt and dc1_fgt. Exhibit B shows the system global and system settings configuration on dc1_fgt.
When branch1_client establishes a connection to dc1_host, the administrator observes that, on dc1_fgt, the reply traffic is routed over T_INET_0_0, even though T_INET_1_0 is the preferred member in the matching SD-WAN rule.
Based on the information shown in the exhibits, what configuration change must be made on dc1_fgt so dc1_fgt routes the reply traffic over T_INET_1_0?
- A. Disable allow-subnet-overlap under config system settings.
- B. Enable auxiliary-session under config system settings.
- C. Enable snat-route-change under config system global.
- D. Disable tcp-session-without-syn under config system settings.
Answer: B
Explanation:
Controlling return path with auxiliary session When multiple incoming or outgoing interfaces are used in ECMP or for load balancing, changes to routing, incoming, or return traffic interfaces impacts how an existing sessions handles the traffic. Auxiliary sessions can be used to handle these changes to traffic patterns.https://docs.fortinet.com/document/fortigate/7.0.11/administration-guide/14295/controlling-return-path-with-auxiliary-session
NEW QUESTION # 21
What are two reasons why FortiGate would be unable to complete the zero-touch provisioning process? (Choose two.)
- A. The zero-touch provisioning process has completed internally, behind FortiGate.
- B. The FortiGate cloud key has not been added to the FortiGate cloud portal.
- C. FortiDeploy has connected with FortiGate and provided the initial configuration to contact FortiManager
- D. A factory reset performed on FortiGate.
- E. FortiGate has obtained a configuration from the platform template in FortiGate cloud.
Answer: A,B
NEW QUESTION # 22
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit A shows an SD-WAN event log and exhibit B shows the member status and the SD-WAN rule configuration.
Based on the exhibits, which two statements are correct? (Choose two.)
- A. Port2 has the highest member priority.
- B. FortiGate updated the outgoing interface list on the rule so it prefers port2.
- C. SD-WAN rule ID 1 is set to lowest cost (SLA) mode.
- D. Port2 has a lower latency than port1.
Answer: B,D
NEW QUESTION # 23
Which two tasks are part of using central VPN management? (Choose two.)
- A. You configure VPN communities to define common IPsec settings shared by all VPN gateways.
- B. You must enable VPN zones for SD-WAN deployments.
- C. FortiManager installs VPN settings on both managed and external gateways.
- D. You can configure full mesh, star, and dial-up VPN topologies.
Answer: A,D
NEW QUESTION # 24
Refer to the exhibits.
Exhibit A -
Exhibit B -
Exhibit A shows a site-to-site topology between two FortiGate devices: branch1_fgt and dc1_fgt. Exhibit B shows the system global and system settings configuration on dc1_fgt.
When branch1_client establishes a connection to dc1_host, the administrator observes that, on dc1_fgt, the reply traffic is routed over T_INET_0_0, even though T_INET_1_0 is the preferredmember in the matching SD-WAN rule.
Based on the information shown in the exhibits, what configuration change must be made on dc1_fgt so dc1_fgt routes the reply traffic over T_INET_1_0?
- A. Disable allow-subnet-overlap under config system settings.
- B. Enable auxiliary-session under config system settings.
- C. Enable snat-route-change under config system global.
- D. Disable tp-session-without-syn under config system settings.
Answer: B
Explanation:
Explanation
Controlling return path with auxiliary session When multiple incoming or outgoing interfaces are used in ECMP or for load balancing, changes to routing, incoming, or return traffic interfaces impacts how an existing sessions handles the traffic. Auxiliary sessions can be used to handle these changes to traffic patterns.https://docs.fortinet.com/document/fortigate/7.0.11/administration-guide/14295/controlling-return-path-
NEW QUESTION # 25
Refer to the exhibit, which shows the IPsec phase 1 configuration of a spoke.
What must you configure on the IPsec phase 1 configuration for ADVPN to work with SD-WAN?
- A. You must disable idle-timeout.
- B. You must enable auto-discovery-sender.
- C. You must enable net-device.
- D. You must set ike-version to 1.
Answer: C
NEW QUESTION # 26
Refer to the exhibits.
Exhibit A
Exhibit B -
Exhibit A shows the configuration for an SD-WAN rule and exhibit B shows the respective rule status, the routing table, and the member status.
The administrator wants to understand the expected behavior for traffic matching the SD-WAN rule.
Based on the exhibits, what can the administrator expect for traffic matching the SD-WAN rule?
- A. The traffic will be load balanced across all three overlays.
- B. The traffic will be routed over T_MPLS_0.
- C. The traffic will be routed over T_INET_0_0.
- D. The traffic will be routed over T_INET_1_0.
Answer: D
NEW QUESTION # 27
Which are three key routing principles in SD-WAN? (Choose three.)
- A. By default, SD-WAN rules are skipped if the best route to the destination is not an SD-WAN member.
- B. By default, SD-WAN members are skipped if they do not have a valid route to the destination.
- C. FortiGate performs route lookups for new sessions only.
- D. SD-WAN rules have precedence over ISDB routes.
- E. Regular policy routes have precedence over SD-WAN rules.
Answer: A,B,E
NEW QUESTION # 28
Refer to the exhibit, which shows the IPsec phase 1 configuration of a spoke.
What must you configure on the IPsec phase 1 configuration for ADVPN to work with SD-WAN?
- A. You must disable idle-timeout.
- B. You must enable auto-discovery-sender.
- C. You must enable net-device.
- D. You must set ike-version to 1.
Answer: C
NEW QUESTION # 29
Refer to the exhibits.
Which conclusion about the packet debug flow output is correct?
- A. The packet size exceeded the outgoing interface MTU.
- B. The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.
- C. The number of concurrent sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the firewall policy, and the packet was dropped.
- D. The total number of daily sessions for 10.1.10.1 exceeded the maximum number of concurrent sessions configured in the traffic shaper, and the packet was dropped.
Answer: B
Explanation:
In a Per-IP shaper configuration, if an IP address exceeds the configured concurrent session limit, the message "Denied by quota check" appears. SD-WAN 7.0 Study Guide page 287
NEW QUESTION # 30
Refer to the exhibit.
The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?
- A. When T_MPLS_0 has a latency of 100 ms.
- B. When T_INET_0_0 has a latency of 250 ms.
- C. When T_INET_0_0 and T_MPLS_0 have the same latency.
- D. When T_N1PLS_0 has a latency of 80 ms.
Answer: D
NEW QUESTION # 31
In the default SD-WAN minimum configuration, which two statements are correct when traffic matches the default implicit SD-WAN rule? (Choose two )
- A. Traffic has matched none of the FortiGate policy routes.
- B. An absolute SD-WAN rule was defined and matched traffic.
- C. The FIB lookup resolved interface was the SD-WAN interface.
- D. Matched traffic failed RPF and was caught by the rule.
Answer: A,C
NEW QUESTION # 32
Refer to the exhibit.
Which configuration change is required if the responder FortiGate uses a dynamic routing protocol to exchange routes over IPsec?
- A. add-route must be disabled.
- B. mode-cfg must be enabled.
- C. exchange-interface-ip must be enabled.
- D. type must be set to static.
Answer: A
Explanation:
Explanation
for using "non ike" routes (for example BGP/static and so on) you must do disable the add-route that inject automatically kernel route based on p2 selectors from the remote site from the SD-WAN_7.2_Study_Guide page 236
NEW QUESTION # 33
Refer to the exhibit.
The device exchanges routes using IBGP.
Which two statements are correct about the IBGP configuration and routing information on the device? (Choose two.)
- A. Each BGP route is three hops away from the destination.
- B. additional-path is enabled.
- C. ibgp-multipath is disabled.
- D. You can run the get router info routing-table database command to display the additional paths.
Answer: B,D
NEW QUESTION # 34
Refer to the exhibit.
Two hub-and-spoke groups are connected through a site-to-site IPsec VPN between Hub 1 and Hub 2.
Which two configuration settings are required for Toronto and London spokes to establish an ADVPN shortcut? (Choose two.)
- A. On the hubs, auto-discovery-sender must be enabled on the IPsec VPNs to spokes.
- B. auto-discovery-forwarder must be enabled on all IPsec VPNs.
- C. On the hubs, net-device must be enabled on all IPsec VPNs.
- D. On the spokes, auto-discovery-receiver must be enabled on the IPsec VPN to the hub.
Answer: A,D
NEW QUESTION # 35
Which diagnostic command can you use to show the member utilization statistics measured by performance SLAs for the last 10 minutes?
- A. diagnose sys sdwan intf-sla-log
- B. diagnose sys sdwan log
- C. diagnose sys sdwan health-check
- D. diagnose sys sdwan sla-log
Answer: D
NEW QUESTION # 36
Refer to the exhibit.
Which algorithm does SD-WAN use to distribute traffic that does not match any of the SD-WAN rules?
- A. All traffic from a source IP is sent to the same interface.
- B. All traffic from a source IP is sent to the most used interface.
- C. All traffic from a source IP to a destination IP is sent to the least used interface.
- D. All traffic from a source IP to a destination IP is sent to the same interface.
Answer: D
NEW QUESTION # 37
Refer to the exhibit.
The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured packet loss will make T_INET_1_0 the new preferred member?
- A. When T_INET_1_0 has 4% packet loss.
- B. When T_INET_0_0 has 4% packet loss.
- C. When all three members have the same packet loss.
- D. When T_INET_0_0 has 12% packet loss.
Answer: C
NEW QUESTION # 38
Refer to the exhibits.
Exhibit A -
Exhibit B -
Exhibit A shows the SD-WAN performance SLA and exhibit B shows the SD-WAN member status, the routing table, and the performance SLA status.
If port2 is detected dead by FortiGate, what is the expected behavior?
- A. Host 8.8.8.8 is reachable through port1 and port2.
- B. The administrator manually restores the static routes for port2, if port2 becomes alive.
- C. Port2 becomes alive after three successful probes are detected.
- D. FortiGate removes all static routes for port2.
Answer: D
Explanation:
This is due to Update static route is enable which removes the static route entry referencing the interface if the interface is dead
NEW QUESTION # 39
Which two interfaces are considered overlay links? (Choose two.)
- A. GRE
- B. IPsec
- C. Physical
- D. LAG
Answer: A,B
NEW QUESTION # 40
Refer to the exhibit.
The exhibit shows the BGP configuration on the hub in a hub-and-spoke topology. The administrator wants BGP to advertise prefixes from spokes to other spokes over the IPsec overlays, including additional paths. However, when looking at the spoke routing table, the administrator does not see the prefixes from other spokes and the additional paths.
Based on the exhibit, which three settings must the administrator configure inside each BGP neighbor group so spokes can learn other spokes prefixes and their additional paths? (Choose three.)
- A. Set adv-additional-path to the number of additional paths to advertise
- B. Enable soft-reconfiguration
- C. Set additional-path to send
- D. Set advertisement-interval to the number of additional paths to advertise
- E. Enable route-reflector-client
Answer: A,C,E
NEW QUESTION # 41
......
Fortinet NSE7_SDW-7.0 certification is an essential credential for network security professionals who want to stay ahead in the industry. It validates the skills and knowledge required to design, implement, and manage secure SD-WAN solutions. Fortinet NSE 7 - SD-WAN 7.0 certification is highly valued by employers and is a testament to the proficiency of the certified professional in the field of secure SD-WAN deployment and management.
Pass Guaranteed Quiz 2024 Realistic Verified Free Fortinet: https://www.realvce.com/NSE7_SDW-7.0_free-dumps.html
NSE7_SDW-7.0 Exam Questions - Real & Updated Questions PDF: https://drive.google.com/open?id=1PupcvN2bgVAlAGSqyh881GivYOPBPyWv