Get ready to pass the JN0-663 Exam right now using our JNCIP-SP Exam Package
A fully updated 2021 JN0-663 Exam Dumps exam guide from training expert RealVCE
NEW QUESTION 11
Exhibit:
Which two statements regarding the output shown in the exhibit are correct? (Choose two.)
- A. The type of connection is local.
- B. The label associated with this virtual circuit is out of range.
- C. The PEs have matching control word values.
- D. The type of connection is remote.
Answer: C
NEW QUESTION 12
Which two statements about IS-IS are correct? (Choose two.)
- A. A Level 1 router can only form adjacencies with other Level 1 routers.
- B. Level 1 intermediate systems exchange routing information with Level 1 intermediate systems on other IS-IS areas.
- C. Level 2 routers can form adjacencies with either Level 1 or Level 2 routers.
- D. An IS-IS router sets the attached bit in the PDUs it sends to a Level 1 area to indicate that it is a backbone router.
Answer: A,D
NEW QUESTION 13
Exhibit:
R2 is receiving the same route from R1 and R3. You must ensure that you can load balance traffic for that route.
Referring to the exhibit, which two configuration changes will allow load balancing? (Choose two.)
- A. Apply the prepend policy as an import policy under group R3.
- B. Configure muitipath under the global BGP configuration.
- C. Apply the prepend policy as an import policy under group R1.
- D. Configure muitipath under group R1.
Answer: B,C
NEW QUESTION 14 
You are the administrator of AS 65512. You are learning the 192.168.1.0/24 prefix from both AS 100 and AS 200. You want traffic destined to the 192.168.1.0.0/24 prefix to exit your AS towards AS 200.
How would you accomplish this task?
- A. Configure an import routing policy on PE-2 to modify the origin attribute on the path learned from AS
100. - B. Configure an import routing policy on PE-2 to append the AS path attribute on the path learned from AS
100. - C. Configure an import routing policy on PE-2 to set a higher local preference value on the path learned from AS 200.
- D. Configure an import routing policy on PE-2 to set a higher MED on the path learned from AS 100.
Answer: C
NEW QUESTION 15 
Referring to the exhibit, which path would traffic passing through R1 take to get to R6?
- A. R1 -> R3 -> R5 -> R6
- B. R1 -> R2 -> R3 -> R6
- C. R1 -> R3 -> R4 -> R6
- D. R1 -> R2 -> R4 -> R6
Answer: A
Explanation:
Explanation/Reference:
NEW QUESTION 16
Exhibit:
Referring to the exhibit, you are asked to summarize all routes in the 10.10.0 0/22 address range ensuring that a single summary route is present in area 49.0002 while the IS-IS internal contributing routes are restricted to area 49.0001. All other routes must not be affected.
Which two operations would have to be performed on R2 to accomplish this task? (Choose two.)
- A. Create and apply a policy with a single term to accept only the summary route.
- B. Include the from level 1 match criteria when referencing the summary route.
- C. Create and apply a policy with two terms; one to accept the summary route and one to reject the contributing routes.
- D. Include the to level 2 match criteria when referencing the summary route.
Answer: C,D
NEW QUESTION 17
Exhibit:
Referring to the exhibit, a Layer 3 VPN is configured, however, the routes are being hidden.
What is the problem?
- A. An active MPLS tunnel does not exist between the peers.
- B. A VRF target community mismatch exists between the peers.
- C. A route distinguisher mismatch exists between the peers.
- D. The BGP peer is not reachable through the IGP.
Answer: A
NEW QUESTION 18
Exhibit:
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The vrf-target configuration stops routes from being shared between CE-1 and CE-2.
- B. The route-distinguisher configuration allows routes to be shared between CE-1 and CE-2.
- C. The route-distinguisher configuration stops routes from being shared between CE-1 and CE-2.
- D. The vrf-target configuration allows routes to be shared between CE-1 and CE-2.
Answer: A,B
NEW QUESTION 19
Exhibit:
You must configure an OSPF virtual link to facilitate communication between Area 0 and Area 20.
Referring to the exhibit, which two addresses should you use as the neighbor IDs of the virtual link endpoints?
(Choose two.)
- A. The address that is associated with R2's xe-1/2/0 interface.
- B. The address that is associated with R4's xe-0/0/1 interface.
- C. The address that is associated with R4's router ID.
- D. The address that is associated with R2's router ID.
Answer: C,D
NEW QUESTION 20
Exhibit:
Your network is connected to two different ISPs and you notice that they are using your network for transit traffic.
In this scenario, which two configuration statements will solve this problem? (Choose two.)
- A. set policy-options policy-statement ISP term REST then reject
- B. set policy-options as-path LOCAL-ROUTES " (65310 I 65441) +"
- C. set policy-options policy-statement ISP term ROUTES then reject
- D. set policy-options as-path LOCAL-ROUTES "()"
Answer: A,D
NEW QUESTION 21
Exhibit:
Referring to the exhibit, external routes are being received at R1. These routes must appear on R5.
Which action will produce this result?
- A. Write an export policy on R4 from level 2 to level 1 matching the external routes.
- B. Turn on wide metrics on R4 and R5 and write an export policy on R2 from level 1 to level 2 matching the external routes.
- C. Turn on wide metrics on R1 and R2 and write an export policy on R4 from level 2 to level 1 matching the external routes.
- D. Write an export policy on R2 from level 1 to level 2 matching the external routes.
Answer: C
NEW QUESTION 22 
Referring to the exhibit, which three statements about route 10.222/16 are correct when using the default BGP advertisement rules? (Choose three)
- A. R2 will prepend AS10 when advertising 10.222/16 to R7.
- B. R2 will advertise 10.222/16 to R4 with itself as the next hop.
- C. R7 will advertise 10.222/16 to R9 with itself as the next hop.
- D. R1 will prepend AS10 when advertising 10.222/16 to R2.
- E. R1 will advertise 10.222/16 to R2 with itself as the next hop.
Answer: A,B,C
NEW QUESTION 23
Exhibit:
Referring to the exhibit, a Layer 3 VPN is configured, however, the routes are being hidden.
What is the problem?
- A. An active MPLS tunnel does not exist between the peers.
- B. A VRF target community mismatch exists between the peers.
- C. A route distinguisher mismatch exists between the peers.
- D. The BGP peer is not reachable through the IGP.
Answer: A
NEW QUESTION 24
Which two statements regarding Ethernet segments (ES) are correct? (Choose two.)
- A. The Type-2 EVPN route will indicate if there is a designated forwarder on the ES.
- B. The Type-1 EVPN route will indicate if the ES is all-active or single-active.
- C. The Type-3 EVPN route will be used for the aliasing function to load-balance to the ES.
- D. The Type-4 EVPN route will be used to elect the designated forwarder for the ES.
Answer: B,D
NEW QUESTION 25
Exhibit:
You are receiving the same 200.0.0.0/24 BGP route from four different ISPs.
Referring to the exhibit, which ISP's route would be selected as active?
- A. ISP-A
- B. ISP-D
- C. ISP-B
- D. ISP-C
Answer: B
NEW QUESTION 26
Exhibit:
Referring to the exhibit, you want to reduce the CPU processing load on PE 2 by preventing the receipt of routes belonging to Customer B.
In this scenario, which Layer 3 VPN scaling mechanism provides this functionality?
- A. route refresh
- B. route target filtering
- C. route origin
- D. route reflection
Answer: B
NEW QUESTION 27
Exhibit:
All networks shown in the exhibit contain more than one BGP speaker You operate ISP A and must ensure that Customer Y sends their traffic to you over the directly connected link. Customer Y is not to be used for transit into your network.
What would you do to accomplish this task?
- A. Advertise routes to Customer Y with the custom defined 65535:65535 community.
- B. Advertise routes to Customer Y with the well-known no-export community
- C. Advertise routes to Customer X with the well-known no-advertise community.
- D. Advertise routes to Customer X with the custom defined 0:0 community
Answer: B
NEW QUESTION 28
Exhibit:
R4 is directly connected to both RPs (R2 and R3). R4 is currently sending all joins upstream to R3 but you want to load balance the joins between both RPs Referring to the exhibit, which configuration change will solve this issue?
- A. Configure the join-load-balance parameter under PIM on R4.
- B. Configure the bootstrap priority on R2 to be the same as R3.
- C. Configure the default route in inet.2 on R4 from R3 as the next hop to both R3 and R2.
- D. Configure the group-range parameter to be the same on R2 and RCA
Answer: A
NEW QUESTION 29
Exhibit:
Traffic is being sent from R2 to R3. The link between R2 and R3 fails.
Referring to the exhibit, which statement is correct?
- A. Manual intervention is required for traffic to be rerouted.
- B. Traffic will automatically reroute distributed between all available paths.
- C. Traffic will automatically reroute using R2 to R4 to R1 to R3.
- D. Traffic will automatically reroute using the shortest path, which is R2 to R1 to R3.
Answer: C
NEW QUESTION 30
Exhibit:
Traffic is being sent from R2 to R3. The link between R2 and R3 fails.
Referring to the exhibit, which statement is correct?
- A. Manual intervention is required for traffic to be rerouted.
- B. Traffic will automatically reroute distributed between all available paths.
- C. Traffic will automatically reroute using R2 to R4 to R1 to R3.
- D. Traffic will automatically reroute using the shortest path, which is R2 to R1 to R3.
Answer: C
NEW QUESTION 31
Exhibit:
The exhibit shows a BGP peering session for two PE routers. The BGP session is up, but the hosts in the Layer
2 VPN that uses the BGP session are unable to communicate.
What is the problem in this situation?
- A. The local BGP router does not support Layer 2 VPN and Layer 3 VPN NLRI address families at the same time.
- B. There is a mismatch in the supported NLRI address families between the BGP peers.
- C. The BGP peer does not support the add-path feature.
- D. The BGP peer does not support the restarter functionality.
Answer: B
NEW QUESTION 32
Exhibit:
Which two statements regarding the output shown in the exhibit are correct? (Choose two.)
- A. The type of connection is remote.
- B. The type of connection is local.
- C. The label associated with this virtual circuit is out of range.
- D. The PEs have matching control word values.
Answer: A,D
NEW QUESTION 33
Exhibit:
Referring to the exhibit, external routes are being received at R1. These routes must appear on R5.
Which action will produce this result?
- A. Write an export policy on R4 from level 2 to level 1 matching the external routes.
- B. Turn on wide metrics on R4 and R5 and write an export policy on R2 from level 1 to level 2 matching the external routes.
- C. Turn on wide metrics on R1 and R2 and write an export policy on R4 from level 2 to level 1 matching the external routes.
- D. Write an export policy on R2 from level 1 to level 2 matching the external routes.
Answer: C
NEW QUESTION 34 
Referring to the exhibit, which statement is true?
- A. The BGP session between R1 and R2 will fail to establish correctly due to an NLRI mismatch.
- B. The BGP session between R1 and R2 will establish correctly and only the inet6 unicast NLRI will pass routing information.
- C. The BGP session between R1 and R2 will establish correctly and the inet unicast and the inet6 unicast NLRIs will pass routing information.
- D. The BGP session between R1 and R2 will establish correctly and only the inet unicast NLRI will pass routing information.
Answer: D
NEW QUESTION 35
Exhibit:
Referring to the exhibit, which two statements are true? (Choose two.)
- A. The vrf-target configuration stops routes from being shared between CE-1 and CE-2.
- B. The route-distinguisher configuration allows routes to be shared between CE-1 and CE-2.
- C. The route-distinguisher configuration stops routes from being shared between CE-1 and CE-2.
- D. The vrf-target configuration allows routes to be shared between CE-1 and CE-2.
Answer: A,B
NEW QUESTION 36
......
Master 2021 Latest The Questions JNCIP-SP and Pass JN0-663 Real Exam!: https://www.realvce.com/JN0-663_free-dumps.html
Practice To JN0-663 - RealVCE Remarkable Practice On your Service Provider Routing and Switching, Professional (JNCIP-SP) Exam: https://drive.google.com/open?id=1seKJiEEPDf70_TbA_gDgzld57mhu4cb6