Many people know getting HP certification is very useful for their career but they fear failure because they hear it is difficult. Now I advise you to purchase our HP0-Y36 premium VCE file. If you are not sure you can download our HP0-Y36 VCE file free for reference. Please trust me if you pay attention on our HP0-Y36 dumps VCE pdf you will not fail. We can guarantee you pass HP0-Y36 exam 100%.

Why do we have this confidence to say that we are the best for HP0-Y36 exam and we make sure you pass exam 100%? Because our premium VCE file has 80%-90% similarity with the real HP HP0-Y36 questions and answers. Once you finish our HP0-Y36 dumps VCE pdf and master its key knowledge you will pass HP0-Y36 exam easily. If you can recite all HP0-Y36 dumps questions and answers you will get a very high score. Our standard is that No Help, Full Refund. No pass, No pay.

Instant Download: Our system will send you the HP0-Y36 braindumps file you purchase in mailbox in a minute after payment. (If not received within 12 hours, please contact us. Note: don't forget to check your spam.)

HP HP0-Y36 Exam Syllabus Topics:

HP Deploying HP Enterprise Networks Sample Questions:

1. Click the Exhibit button.
All network routers shown in the exhibit are configured for OSPF and MPLS on all interfaces. Router P-3 and Router P-5 have two directly-connected LDP peers. Traffic from Router PE-1 destined for IP address 15.2.2.2 is label-swapped from P-3 to P-4.A link

between Router P-3 and
P-5 is introduced, but MPLS is not enabled on this new interface. The OSPF cost of the new link is smaller than the OSPF cost of the link from P-4 to P-5.Which statement is true about packets from PE-1 destined for IP address 15.2.2.2?

A) Router P-3 will continue to send these packets to P-4 with an MPLS label.
B) Router P-3 will send these packets directly to P-5 with an MPLS label.
C) Router PE-1 will send these packets to P-3 without an MPLS label.
D) Router P-3 will send these packets directly to P-5 without an MPLS label.

2. In your IRF stack, you execute the display bfd session command and confirm the BFD session is active. What does this outcome indicate about the status of your IRF stack?

A) The IRF stack has split.
B) The IRF stack is electing a new Slave.
C) The IRF priorities are set at default values.
D) The IRF stack is performing as expected.

3. Click the Exhibit button and view both exhibits.


AS 20 advertises prefix 20.0.0.0 /8, and AS 30 advertises prefix 30.0.0.0 /8. On Router-3,
what is the BGP Next Hop attribute for prefix 20.0.0.0 /8?

A) 16.3.3.1
B) 16.2.2.1
C) 30.1.1.1
D) 16.0.0.3
E) 16.0.0.1
F) 20.1.1.1

4. Click the Exhibit button.

Router-1 and Router-2 are BGP peers. Router-2 and Router-3 are BGP peers. However, Router-3 has not learned the 16.0.0.0/8 BGP route. How can you resolve this issue? (Select two.)

A) Establish a physical link between Router-1 and Router-3.
B) Configure Router-2 as a route reflector and Router-1 and Router-3 as clients.
C) Prepend AS1 to the 16.0.0.0/8 route on Router-1.
D) Adjust the local preference of 16.0.0.0/8 on Router-1.
E) Enable BGP peering between Router-1 and Router-3.
F) Enable IGP synchronization on all routers.

5. Prefixes from two different customers are advertised between two Provider Edge routers using Multi-Protocol BGP. Which feature of MPLS Layer-3 VPNs allows these prefixes to be placed into the proper VPN routing table?

A) address family indicator
B) route distinguisher
C) MBGP
D) MPLS EXP bits
E) VPN target

Solutions: